Another Newbie. Please Help

OldFoo · Post by **OldFoo** » Thu Jul 03, 2008 3:36 am

yea I figured that the harness would end up a pain but I have a local source who does arcade repair and other stuff for a living but the majority I can do myself. The Bezel has room to put stuff in it. Whats bugn me now is what the res is on the monitor. To hit even more of a snag my Naomi system has that freakin version A converter. So anybody with a capcom I/O hit me up. The cabinet is JAMMA.

OldFoo · Post by **OldFoo** » Thu Jul 03, 2008 3:57 am

69NovaSS wrote:yea I figured that the harness would end up a pain but I have a local source who does arcade repair and other stuff for a living but the majority I can do myself. The Bezel has room to put stuff in it. Whats bugn me now is what the res is on the monitor. To hit even more of a snag my Naomi system has that freakin version A converter. So anybody with a capcom I/O hit me up. The cabinet is JAMMA.

Your Version A SEGA JAMMA converter should be fine.

(For games w/ joystick and buttons - not shooters)

It will be powered from JAMMA interface

You just need a seperate power supply for the naomi (cheap)

This thread might help.

http://www.sega-naomi.com/forum/viewtopic.php?t=982

(Towards the end of the thread when I switched from JVS to JAMMA)

Bob Presutti

P.S. (For shooters I am pretty sure you will need a SEGA JVS I/O and ALOT more wiring)

OldFoo · Post by **OldFoo** » Thu Jul 03, 2008 7:34 am

69NovaSS wrote:I personaly don't like gauntlet so I was going to gut it.

If you want to sell the boards lemme know :smt020

OldFoo · Post by **OldFoo** » Thu Jul 03, 2008 11:08 am

you can switch Gauntlet from Std Res to Med Res, so the monitor is most likely a Std Res, if you look on the U12 dip I think #1 is the Res, if ON I recall is Med and OFF is Std, but yes that cabinet makes a lot more sense for a shooter. I have a JVS Setup if you need one, thanks

OldFoo · Post by **OldFoo** » Thu Jul 03, 2008 1:00 pm

I'll keep that in mind english. The thing is that I bought a Naomi of ebay and it should be arriving any day now. Although I have researched the system decently I believe. I have a pretty good knowledge in other home arcade systems as I own a few other machines with this being my first Naomi system. I read the starter Naomi page on the FAQ forums and seen where I need the JVS. How does that work? Do I need to run a straight JVS to get hod2 to work? :smt017 I knew from the beginning this would be a hell of a project. But I feel like it'll be worth it in the end

OldFoo · Post by **OldFoo** » Thu Jul 03, 2008 1:52 pm

69NovaSS wrote:I'll keep that in mind english. The thing is that I bought a Naomi of ebay and it should be arriving any day now. Although I have researched the system decently I believe. I have a pretty good knowledge in other home arcade systems as I own a few other machines with this being my first Naomi system. I read the starter Naomi page on the FAQ forums and seen where I need the JVS. How does that work? Do I need to run a straight JVS to get hod2 to work? :smt017 I knew from the beginning this would be a hell of a project. But I feel like it'll be worth it in the end

For shooters.

Naomi connect to JVS via USB

Gun I/O board connects to JVS via harness

(see other thread for specifics and scematic link)

IR sensor array connects to Gun I/O Board via harness

Guns connect to Gun I/O Board via harness

Player 1/2 Start connect to JVS I/O

OldFoo · Post by **OldFoo** » Thu Jul 03, 2008 5:17 pm

Ok got it. I really appreciate the help. As soon as I get my board I'll be able to begin work :smt066 :smt066