Page 1 of 2
Friend needs help with a sitdown Crazy Taxi
Posted: Wed Jul 21, 2010 6:05 pm
by OldFoo
Hey guys this guy messaged me on youtube a few days ago and is having some trouble with his crazy taxi machine, none of the controls are registering. Here is the vid, if you can help him out im sure he would really appreciate it. Thanks
http://www.youtube.com/watch?v=3TsNYOhD ... ture=email
Posted: Wed Jul 21, 2010 6:13 pm
by OldFoo
you should have 3 wires on the pot, the outer two should read 5v, the inner one should go from 0-5
if not 0-5, check the connector into i/o board.
download schematic, and check voltage coming out of analog port on i/o board.
Posted: Thu Jul 22, 2010 1:52 am
by OldFoo
I am the Dude need help !! Hi!!
:smt004
the 3 Wires on the Pot??
My I/O board did power up . i really need the schematic. where can i download one. thanks
Posted: Thu Jul 22, 2010 2:12 am
by OldFoo
Posted: Thu Jul 22, 2010 2:14 am
by OldFoo
avcc = 5v , agnd = gnd
check to make sure you have +5/+12 going to i/o
did you go into test, and do jvs test from there?
Posted: Thu Jul 22, 2010 2:40 am
by OldFoo
KI4SWY wrote:avcc = 5v , agnd = gnd
check to make sure you have +5/+12 going to I/o
did you go into test, and do jvs test from there?
the schematic is not for my 2000 . Wiring Diag.
I am able go to Test mode
Posted: Thu Jul 22, 2010 6:17 am
by OldFoo
compoko wrote:KI4SWY wrote:avcc = 5v , agnd = gnd
check to make sure you have +5/+12 going to I/o
did you go into test, and do jvs test from there?
the schematic is not for my 2000 . Wiring Diag.
I am able go to Test mode
and were you able to run the JVS test?
What wiring diagram are you referring to, if the link provided is not the correct one? BTW, the JVS I/O pinout is here:
http://triplemoonstar.brinkster.net/the ... ockid=1718
Posted: Thu Jul 22, 2010 11:16 am
by OldFoo
the basic wiring diagram should be the same.
Do you have a Crazy Taxi or a Crazy Taxi High Roller ?
What part # is on your I/O ?
What does the JVS Test say? Does it report no I/O found ?
If no i/o found, is there power to the JVS I/O ?
Posted: Fri Jul 23, 2010 2:06 pm
by OldFoo
KI4SWY wrote:the basic wiring diagram should be the same.
Do you have a Crazy Taxi or a Crazy Taxi High Roller ?
What part # is on your I/O ?
What does the JVS Test say? Does it report no I/O found ?
If no I/o found, is there power to the JVS I/O ?
Yes I am able to go to test mode. also the JVS I/O power is up and have its power to CN7 and i slo try CN8 both CN7 and CN8 will power up the JVS I/O
Then i went to test mode check the input for the buttons.
everything works fine except the ACC/Brake and Handle.
what did i do wrong?
thanks Guys !!!
CN7 4pin JST NH connector (5V Power in)
------------------------------------------------------
01 +5v
02 +5v
03 GND
04 GND
CN8 4pin JST NH connector (5V Power out)
------------------------------------------------------
01 +5v
02 +5v
03 GND
04 GND
Posted: Fri Jul 23, 2010 2:11 pm
by OldFoo
KI4SWY wrote:the basic wiring diagram should be the same.
Do you have a Crazy Taxi or a Crazy Taxi High Roller ?
What part # is on your I/O ?
What does the JVS Test say? Does it report no I/O found ?
If no I/o found, is there power to the JVS I/O ?
I have the Crazy Taxi Sit down. and my board is 837-13551 without - 92.
i look at the web and seen only able to find 837-13551-92 what's up witht he -92 are they the same?
It found all the keys tested ok except the ACC/BRK/ HANDLE they all have funny number like dfh...and its jumping when i move the other keys...
if you see my video you can see the dfh flicking...while i am trying the other buttons.
thanks thanks