Monkey Ball with Banana Stick not work? Help

OldFoo · Post by **OldFoo** » Thu Jul 03, 2008 8:09 pm

I have Monkeyball with the B.Stick.

When I make in my Naomi net city the stick not work.

Only start work!

Where is the Problem???

Thanks

OldFoo · Post by **OldFoo** » Thu Jul 03, 2008 9:49 pm

The Banana stick is an analog joystick, in contrast to the digital joystick that probably was on the CP that you pulled from the cab.

Try reading this post first:

http://www.sega-naomi.com/forum/viewtopic.php?t=1742

OldFoo · Post by **OldFoo** » Thu Jul 03, 2008 10:05 pm

It looks from the picture that you cabinet is a JPN with Tyco connectors.

Also based on the fact you are in germany I would also guess your cabinet is JPN with Tyco connectors.

If so all you need is the 'Y' harness. (Not expensive)

Geezer has them.

NOA-60061 [Analogue Splitter Loom]

This is the analogue splitter loom and is required for several analogue control panels Sega made, such as Monkey Ball and Zombie Revenge.

http://triplemoonstar.brinkster.net/seg ... ockid=1733

Hook one end to player 1 and 2 analog conectors on cabinet

The other end to analog connector on Monkey Ball panel

Bob Presutti

OldFoo · Post by **OldFoo** » Fri Jul 04, 2008 6:04 am

SkiDog wrote:It looks from the picture that you cabinet is a JPN with Tyco connectors.

Also based on the fact you are in germany I would also guess your cabinet is JPN with Tyco connectors.

If so all you need is the 'Y' harness. (Not expensive)

Geezer has them.

NOA-60061 [Analogue Splitter Loom]

This is the analogue splitter loom and is required for several analogue control panels Sega made, such as Monkey Ball and Zombie Revenge.

http://triplemoonstar.brinkster.net/seg ... ockid=1733

Hook one end to player 1 and 2 analog conectors on cabinet

The other end to analog connector on Monkey Ball panel

Bob Presutti

Thanks! :smt006

OldFoo · Post by **OldFoo** » Sun Jul 06, 2008 4:34 pm

I think the cabelk is not right!The Plug hast 10 but in naomi hast 15?

Please look on the Picture , the Plug is not right.

OldFoo · Post by **OldFoo** » Sun Jul 06, 2008 5:39 pm

Darky wrote:I think the cabelk is not right!The Plug hast 10 but in naomi hast 15?

Please look on the Picture , the Plug is not right.

Connector 1 goes to connector 1

For the other...

You need to use the two bottom yellow and white 8 pin connectors

The loom from Geezer has two 8 pin connectors on one end (yellow and white) and a 10 pin connector on the other end to plug into your monkey ball panel (connector 2)

Bob Presutti

OldFoo · Post by **OldFoo** » Sun Jul 06, 2008 6:13 pm

SkiDog wrote:
Darky wrote:I think the cabelk is not right!The Plug hast 10 but in naomi hast 15?

Please look on the Picture , the Plug is not right.

Connector 1 goes to connector 1

For the other...

You need to use the two bottom yellow and white 8 pin connectors

The loom from Geezer has two 8 pin connectors on one end (yellow and white) and a 10 pin connector on the other end to plug into your monkey ball panel (connector 2)

Bob Presutti

Thanks !